DAA Turbo Case-Feeder Plate - Pistol all Calibres
Pistol Calibres Only
Pistol Calibres Only
Pistol Calibres Only
In Stock
The DAA Turbo Case-Feeder Plate is a highly modified and evolved reloading accessory which will greatly increase the output speed of your current Dillon case feeder.
The plate is designed to handle all pistol calibres – from .380 to 0.45, so one plate can now handle all your pistol calibres!
** For the very long revolver cases (38SPL and 357) the plate must be elevated using a spacer (large washer or the Armanov Drop-In Spacer) (not included).
Click here for the Armanov Drop-In Spacer
The DAA Turbo Case-Feeder Plate is built very differently from the original Dillon Plate. Our plate is much thicker and incorporate deep feeding grooves into each of the 32 output pockets on the plate. These grooves improve the efficiency of picking up brass as the plate rotates, ensuring that more of the pockets output a case, on each rotation. This increases the output speed by 30-80% compared to the original plate. (Output speed gain varies per calibre. Highest gains are with 9mm, lowest with .45)
The thicker plate design also serves to offer better support to the cases as they drop out the exit hole, reducing the likelihood of them rotating on the way out and possible causing a hang-up in the output funnel.
The DAA Turbo Case-Feeder Plate includes an aluminium slip clutch assembly at its centre, to ensure the disc can slip and not stall the motor if a jam occurs. Our slip-clutch assembly includes a handy stainless-steel D-ring which makes it much easier to grab hold of the plate from its centre and lift it up off the motor shaft, and out the case feeder. (Experienced reloaders will know that this can be difficult to do without such a feature, especially with a well-used, dirty plate/casefeeder)
The 292mm diameter of the DAA Turbo Case-Feeder Plate make it a drop-in fit for both the original AC Dillon case feeder, as well as the newer Variable Speed DC model. It will also fit and can be used in the Hornady case feeder as well.
Each DAA Turbo Case-Feeder Plate ships including the innovative DAA Dislodge-Wedge for Dillon Variable speed Casefeeder (also sold separately). This wedge replaces the original Dillon wedge in the Variable speed case feeder, further improving performance. (Customers not using the Dillon variable speed case feeder, won't use this wedge). This larger, contoured wedge fits down to the base of the plate and eliminates case pinching and jamming, experienced occasionally with the original, smaller Dillon wedge.
Need to output even faster?!
While developing this product, DAA noticed that the Dillon Variable speed motor is wired so that it slows down and speeds up gradually each time the Switch is triggered under the output chute. While running at full speed, our plate was outputting cases in almost every pocket – and triggering this switch very frequently as the cases fall past it down the tube… This led to the motor slowing down significantly... We found that at full speed – the case feeder would slow down and rotate no faster than it did at half speed.
So, to unlock the full potential of the new plate, we found a simple wiring modification to the Dillon motor, which prevents this from happening. once done, the motor does not slow down as much, and we were able to clock output rates of over 12,000 9mm cases per hour!
If you need high output rates (for a commercial Rollsizer, decapper or so on) check out the instructions here: Unlocking the full speed potential of your Dillion Variable Speed Case Feeder
Please note the above modification has not been approved by Dillon.
| SKU | 131813 |
| Brand | Double Alpha Academy |
| Shipping Weight | 0.4500kg |
| Shipping Width | 0.310m |
| Shipping Height | 0.060m |
| Shipping Length | 0.310m |
| Shipping Cubic | 0.005766000m3 |
| Unit Of Measure | ea |
The DAA Turbo Case-Feeder Plate is a highly modified and evolved reloading accessory which will greatly increase the output speed of your current Dillon case feeder.
The plate is designed to handle all pistol calibres – from .380 to 0.45, so one plate can now handle all your pistol calibres!
** For the very long revolver cases (38SPL and 357) the plate must be elevated using a spacer (large washer or the Armanov Drop-In Spacer) (not included).
Click here for the Armanov Drop-In Spacer
The DAA Turbo Case-Feeder Plate is built very differently from the original Dillon Plate. Our plate is much thicker and incorporate deep feeding grooves into each of the 32 output pockets on the plate. These grooves improve the efficiency of picking up brass as the plate rotates, ensuring that more of the pockets output a case, on each rotation. This increases the output speed by 30-80% compared to the original plate. (Output speed gain varies per calibre. Highest gains are with 9mm, lowest with .45)
The thicker plate design also serves to offer better support to the cases as they drop out the exit hole, reducing the likelihood of them rotating on the way out and possible causing a hang-up in the output funnel.
The DAA Turbo Case-Feeder Plate includes an aluminium slip clutch assembly at its centre, to ensure the disc can slip and not stall the motor if a jam occurs. Our slip-clutch assembly includes a handy stainless-steel D-ring which makes it much easier to grab hold of the plate from its centre and lift it up off the motor shaft, and out the case feeder. (Experienced reloaders will know that this can be difficult to do without such a feature, especially with a well-used, dirty plate/casefeeder)
The 292mm diameter of the DAA Turbo Case-Feeder Plate make it a drop-in fit for both the original AC Dillon case feeder, as well as the newer Variable Speed DC model. It will also fit and can be used in the Hornady case feeder as well.
Each DAA Turbo Case-Feeder Plate ships including the innovative DAA Dislodge-Wedge for Dillon Variable speed Casefeeder (also sold separately). This wedge replaces the original Dillon wedge in the Variable speed case feeder, further improving performance. (Customers not using the Dillon variable speed case feeder, won't use this wedge). This larger, contoured wedge fits down to the base of the plate and eliminates case pinching and jamming, experienced occasionally with the original, smaller Dillon wedge.
Need to output even faster?!
While developing this product, DAA noticed that the Dillon Variable speed motor is wired so that it slows down and speeds up gradually each time the Switch is triggered under the output chute. While running at full speed, our plate was outputting cases in almost every pocket – and triggering this switch very frequently as the cases fall past it down the tube… This led to the motor slowing down significantly... We found that at full speed – the case feeder would slow down and rotate no faster than it did at half speed.
So, to unlock the full potential of the new plate, we found a simple wiring modification to the Dillon motor, which prevents this from happening. once done, the motor does not slow down as much, and we were able to clock output rates of over 12,000 9mm cases per hour!
If you need high output rates (for a commercial Rollsizer, decapper or so on) check out the instructions here: Unlocking the full speed potential of your Dillion Variable Speed Case Feeder
Please note the above modification has not been approved by Dillon.
| SKU | 131813 |
| Brand | Double Alpha Academy |
| Shipping Weight | 0.4500kg |
| Shipping Width | 0.310m |
| Shipping Height | 0.060m |
| Shipping Length | 0.310m |
| Shipping Cubic | 0.005766000m3 |
| Unit Of Measure | ea |
We value your opinion.
Leave a reviewWe value your opinion.
Leave a review
Copyright © 2026 David Bailey Enterprises Pty Ltd.
ABN: 19 161 552 736
Address: P.O. Box 8, Bridgewater. TAS 7030
Welcome to our website. If you continue to browse and use this website, you are agreeing to comply with and be bound by the following terms and conditions of use, which together with our privacy policy govern David Bailey Enterprises Pty Ltd’s relationship with you in relation to this website. If you disagree with any part of these terms and conditions, please do not use our website.
The term ‘David Bailey Enterprises Pty Ltd’ or ‘us’ or ‘we’ refers to the owner of the website whose registered office is . Our ABN is 19 161 552 736. The term ‘you’ refers to the user or viewer of our website.
The use of this website is subject to the following terms of use:
This privacy policy sets out how we uses and protects any information that you give us when you use this website.
We are committed to ensuring that your privacy is protected. Should we ask you to provide certain information by which you can be identified when using this website, then you can be assured that it will only be used in accordance with this privacy statement.
We may change this policy from time to time by updating this page. You should check this page from time to time to ensure that you are happy with any changes.
What we collect
We may collect the following information:
What we do with the information we gather
We require this information to understand your needs and provide you with a better service, and in particular for the following reasons:
Security
We are committed to ensuring that your information is secure. In order to prevent unauthorised access or disclosure, we have put in place suitable physical, electronic and managerial procedures to safeguard and secure the information we collect online.
How we use cookies
A cookie is a small file which asks permission to be placed on your computer's hard drive. Once you agree, the file is added and the cookie helps analyse web traffic or lets you know when you visit a particular site. Cookies allow web applications to respond to you as an individual. The web application can tailor its operations to your needs, likes and dislikes by gathering and remembering information about your preferences.
We use traffic log cookies to identify which pages are being used. This helps us analyse data about webpage traffic and improve our website in order to tailor it to customer needs. We only use this information for statistical analysis purposes and then the data is removed from the system.
Overall, cookies help us provide you with a better website by enabling us to monitor which pages you find useful and which you do not. A cookie in no way gives us access to your computer or any information about you, other than the data you choose to share with us.
You can choose to accept or decline cookies. Most web browsers automatically accept cookies, but you can usually modify your browser setting to decline cookies if you prefer. This may prevent you from taking full advantage of the website.
Links to other websites
Our website may contain links to other websites of interest. However, once you have used these links to leave our site, you should note that we do not have any control over that other website. Therefore, we cannot be responsible for the protection and privacy of any information which you provide whilst visiting such sites and such sites are not governed by this privacy statement. You should exercise caution and look at the privacy statement applicable to the website in question.
Controlling your personal information
You may choose to restrict the collection or use of your personal information in the following ways:
We will not sell, distribute or lease your personal information to third parties unless we have your permission or are required by law to do so. We may use your personal information to send you promotional information about third parties which we think you may find interesting if you tell us that you wish this to happen.
If you believe that any information we are holding on you is incorrect or incomplete, please write to or email us as soon as possible. We will promptly correct any information found to be incorrect.
